Shaft Shark pervane koruyucuları

Sevgili Tekne sahipleri,

Geçtiğimiz Şubat ayında sizlere katlanır “Gori “ pervanelerinin temsilciliğine başladığımızı bildirmiştim. Herşeyden önce yoğun ilgi ve taleplerinize teşekkür ederim.Sizden aldığım bu cesaret ile yarışlarımızda ve gezilerimizde başımıza sık sık gelen pervanelerimize dolanan halatları – naylon/benzeri artıkları – ışıklandırılmamış balık ağlarını bertaraf eden yeni bir ürün tanıtmak istiyorum...Evet pervanelerimizi - şaftımızı – saildrive’mızı koruyacak bir K E S İ C İ !!!!

Aşağıda tüm detaylarını göreceğiniz bu ürünün sularımızda emniyetli ve problemsiz seyirlerinize yüksek katkısı olacağı inancındayım.

Sizlere Sağlıklı – Keyifli bir yaz mevsimi dilerim.

Saygılarımla,

Orhan Tuker

What is a SHAFT SHARK?

The SHAFT SHARK is a serrated edge circular blade machined from high quality 316L type stainless steel. It is available as a two-piece/split unit and a single-piece unit. It may be installed on shafts and saildrive systems.

What does it do?

Attached to your shaft just forward of your propeller, it rotates with the shaft or saildrive hub, cutting away any rope, weed or debris that might try to entangle your shaft & propeller.

Why do I need one?

• To keep your propeller free from rope, weeds and underwater debris.

• Eliminate the possibility of damage to your

propeller, strut and cutlass.

• Eliminate the need for being towed due to fouled stern gear or propeller. .

Drag:

The SHAFT SHARK is sized to both the shaft and the propeller or saildrive hub diameter to ensure the lowest possible drag for the boat.

Maintenance:

With no moving parts maintenance is minimal. There are no parts to wear out or to be replaced on an annual basis. The edges can be re-sharpened using a round file or stone.

Installation:

Simple and quick. No drilling or tapping and no need to remove the propeller for installation.

Easily installed underwater by a diver. Models #700 and #900, which are one-piece units, will require removal of the propeller prior to installation.

The SHAFT SHARK requires just a small clearance fore and aft between the cutlass bearing and the propeller hub (see dimension “D” in chart at upper right). This dimension allows for sufficient clearance with the cutlass bearing for shaft movement when maneuvering and for water flow through the cutlass bearing. Always install the SHAFTSHARK as close to the propeller as possible.

Dimensions:

Model #300 (split unit only)

For shaft diameters: 1.00”, 1.125” and 1.25”

25mm and 30mm

Model #400 (split unit only)

For shaft diameters: 1.25”, 1.375”, 1.50” and 1.75” 30, 35, 38 and 40mm

Model #500 (split unit only)

For shaft diameters: 1.25, 1.50, 1.75”, 2.00”, 2.25” and 2.50” 40, 45 and 50mm

Model #600 (split unit only)

For shaft diameters: 2.00”, 2.25”, 2.50”, 2.75”

& 3.00” metric sizes available

Models SS585T, SS695 and SS969 (split unit only)

For Saildrives only

Model #700 (split & single units available)

For shaft diameters: 2.50”, 2.75”, 3.00” and 3.25” metric sizes available

Model #900 (single unit only)

For shaft diameters: 3.50”, 3.75”, 4.00” and 4.50” metric sizes available

Custom shaft sizes available on request.

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

UTL - SKİPER

www.skiper.org

GSM: +905332732985

0 yorum :

Yorum Gönder

ÜYE OLMADAN YORUM YAPABİLİRSİNİZ.
Yazınız denetlendikden sonra yayınlanacakdır.
yazınıza verilen cevapdan haberdar olmak isterseniz, aşağıdaki ( E-posta yoluyla abone ol ) tıklayıp @posta adresinizi yazın onaylayın, yazınıza verilen cevap yorum size @posta olarak bildirilecekdir.